tag:blogger.com,1999:blog-2736339877549700610.post8134895144325258488..comments2017-04-19T04:58:33.569-07:00Comments on EGR 393 Lab Blog Group 7: Week 10 Anonymoushttp://www.blogger.com/profile/13151989436760855350noreply@blogger.comBlogger6125tag:blogger.com,1999:blog-2736339877549700610.post-13063357919884634942017-03-29T14:41:01.835-07:002017-03-29T14:41:01.835-07:00You are right Angel, it is really interesting that...You are right Angel, it is really interesting that MATLAB allows us to use different codes, yet we get the same result and the same graph. Our calculated was lower than 1KHz and because of that our dashed was lower than the one we were supposed to get.Anonymoushttps://www.blogger.com/profile/10479198153363973993noreply@blogger.comtag:blogger.com,1999:blog-2736339877549700610.post-52671799006600887652017-03-29T14:33:23.417-07:002017-03-29T14:33:23.417-07:00 Our values should have been the same but I think ... Our values should have been the same but I think we made a mistake in our measurements, Thanks for your comment moaad.Anonymoushttps://www.blogger.com/profile/10479198153363973993noreply@blogger.comtag:blogger.com,1999:blog-2736339877549700610.post-89159176251547344622017-03-29T14:31:44.502-07:002017-03-29T14:31:44.502-07:00They were supposed to be the same values because w...They were supposed to be the same values because we didn't change our values for the resistor or the capacitor, I think we made a mistake in our measurements but the values for Vout/Vin are close in both measurements.Anonymoushttps://www.blogger.com/profile/10479198153363973993noreply@blogger.comtag:blogger.com,1999:blog-2736339877549700610.post-89403492438665693612017-03-27T04:20:42.266-07:002017-03-27T04:20:42.266-07:00The MATLAB code we both used are similar yet still...The MATLAB code we both used are similar yet still somewhat different which makes it interesting as to how we get the same graph. The dashed line in the low pass filter is at a little bit lower value than we got, but still in the accepted range. Im curious as to who you guys found the cutoff frequency by paper?Anonymoushttps://www.blogger.com/profile/12627358923472982747noreply@blogger.comtag:blogger.com,1999:blog-2736339877549700610.post-68120546442038623192017-03-26T20:39:39.532-07:002017-03-26T20:39:39.532-07:00Not that big difference between our blog and yours...Not that big difference between our blog and yours. Very close data numbers. Also, the MATLAB code are close to each other and it is nice to see how the code could be written in several ways. For the cut if frequency we got the same for the high pass filter and the low pass filter, but you did not. I am not sure why. Moaadhttps://www.blogger.com/profile/09106207870099965682noreply@blogger.comtag:blogger.com,1999:blog-2736339877549700610.post-68580214473465436212017-03-26T18:58:46.196-07:002017-03-26T18:58:46.196-07:00Your high and low pass filter graphs look good but...Your high and low pass filter graphs look good but the cut off frequencies are different, did you change the value of the resistors or capacitors for each? Our high and low pass filter used the same value of resistor and capacitor and they both achieved about the same cut off frequency.Anonymoushttps://www.blogger.com/profile/05808382131717987846noreply@blogger.com